Completed Review - Airfix Hawker Typhoon Ib (A02041)

Scale: 1:72, RRP - £9.99

The last time I'd written about this build was prior to starting the decals. I'd decided to opt for the option depicted on the box art, that of Typhoon MP126, in the markings it carried when flown by Squadron Leader Gerald Stapleton of No.247 Squadron.

In past builds I've found the quality of Airfix's decals to be very good but I had some real problems with those included in this kit. I had several break up on me, including one of the serial numbers, without which I could not complete the build. I don't know if this was a one off, lack of practice on my part or if they were bad decals, although I suspect it was more a case of the first two rather than the latter. Fortunately I had a spare set and they were applied without any further bother, indeed that could said for the rest of the build.

Weathering was once again mostly done by applying Flory Model washes. My previous builds had been very dirty, using the Dark Dirt wash. This time I wanted to refine the weathering. For the undersides I applied a Grey Wash and then for the upper sides I mixed the Grey Wash with Dark Dirt (about a 2:1 ratio) and this gave a more subtle look, which was exactly what I was aiming for.

For the first time I attempted to use oil paints to apply oil streaks but found at this scale I couldn't really get a noticeable, and realistic enough effect. Exhaust marks were airbrushed using Tamiya Smoke, X-19, and dirt was applied to the undersides in small quantities using Flory Models Sand wash.

Again this was another excellent kit from Airfix which I thoroughly enjoyed building. It looks accurate in terms of the detail and shape, and there are two notable decal options. Once I slowed down and started taking some care it went together without any real problems. Although I deviated from the instructions, I don't think that's absolutely necessary, just take care with the flexible lower wing part and you'll be fine.

And that was about it. On a personal note I think this is the best model I've built so far, surpassing my previous build, the Airfix Defiant in the same scale. I think I achieved a more realistic finish, it just took me much longer than I would have liked.

Overall Build Score: 4 out of 5, an excellent release from Airfix with the full options, in-flight or on the ground, open or closed cockpit and pilot figure. Fairly straight forward to build, accurate and with interesting decal options, what more could you ask for?

Purchase:
Enjoyed reading this article? A purchase using the links below will help maintain this blog.

Build Review - Airfix Hawker Typhoon Ib (A02041) – Part 2

For me one of the main objectives of this build was learning to paint late WWII RAF colours correctly. My initial attempt on an Airfix Spitfire had not gone according to plan. Having finally built a Typhoon to my satisfaction I was determined that this time I would get the painting right.

I started by undercoating in a light Tamiya Grey and by pre-shading the panel lines with a flat black. I'm still not 100% convinced that this is worth doing.

Pre-shading

While it seemed to have some effect on the lower, and lighter, surfaces of this particular model it didn't really seem to make much difference on the upper, camouflaged, surfaces. Also I felt that with effect could also be achieved by post-shading and by washes later in the build.

On to painting proper and the undersides. The actual colour for the undersides of RAF aircraft is called Medium Sea Grey. To achieve this I used the following:

1. A base coat of Vallejo MA (Model Air) Barley Grey (71.051). I tried to make sure some of the black panel lines showed through.
2. Vallejo MA Pale Blue Grey (71.046) to the centre of each panel.
3. A thin coat, sprayed at lower pressure, of Vallejo MA Medium Sea Grey (71.049) to selected panel lines to add a slight bit of variation.

RAF Medium Sea Grey & Invasion Stripes

Another objective of this build had been the airbrushing of D-Day invasion stripes. Although this kit came with decals many don't so I thought this would be a good time to practice. The colours used were:

1. An mix of Vallejo MA White and Aged White (71.001 & 71.132). How much depends on how yellow you want it to look. This was applied over the whole area and then masked off in order for the black to be sprayed. It really pays to make sure the masking is tight here, especially in the numerous panel lines.
2. The black was Tamiya Nato Black (XF-69). I prefer using this shade of black at this scale as it's a muted black compared to the XF-1 Black which looks too bright to me.

And with that the lower surfaces were done. I hadn't done the rear invasion stripes yet, as they overlapped onto the upper camouflaged areas.

For the upper surfaces the RAF colours are Ocean Grey and Dark Green. I decided this time to use Tamiya's RAF colours as my starting point (XF81, 82 & 83). If you look the instructions for older Tamiya kits you will see they were all mixes. These are more recent paints which Tamiya brought out to be used with their 1:32 scale Spitfire kits

Starting with the Ocean Grey, this was applied all over and highlighted in the areas that wouldn't be covered with the Dark Green.

1. Tamiya Ocean Grey 2 (XF-82) was mixed with slight amount of Medium Sea Grey (XF-83). The main reason for adding the Meduim Sea Grey was that I felt the base surface with black pre-shade was a bit too dark. Without the pre-shade I would have probably used The Ocean Grey on it's own.
2. I then highlighted panel lines etc with Vallejo MA Barley Grey (71.051). Unfortunately the picture below was taken in bad light and doesn't really show this well.

RAF Ocean Grey

For the Dark Green:

1. I put down a coat of Tamiya Field Grey (XF-65) with a small amount of Dark Green 2 (XF-81). The reason for this was it muted the blue tones from the grey which I was spraying on top of. In previous attempts the green seemed a bit off if I just used XF-81 over the Ocean Grey.
2. I then highlighted the green by using Dark Green (XF-81) on it's own. Of course if you choose to spray each colour over the undercoat, rather than spray an all over Ocean Grey coat, you could probably use this colour on it's own.

RAF Dark Green & Invasion Stripes

The Sky coloured band was then added to the rear fuselage, this was simply Tamiya Sky (XF-21). The invasion stripes were painted the same as before. The one thing I will say is that I found the invasion stripes to the rear fuselage incredibly difficult to do. Getting them straight took numerous attempts due to the curvature of the surface I was applying them to and it used far too much masking tape. It was not helped by the fact that the whole model was masked at this point and fairly hard to judge their position when I had very little of the model exposed.

In the end I had to remove the excess paint with a wooden toothpick in order to get them straight. With hindsight I think would be better to do this first and then mask off the whole invasion band area and spray the camouflage around it.

Despite this last bit killing my enthusiasm for some time I have to say I'm satisfied with the result. I achieved the two things I wanted to, spraying accurate RAF colours and spraying the invasion stripes.

Now onto the decals.

Build Review - Airfix Hawker Typhoon Ib (A02041) – Part 1

As I'd mentioned at the end of a previous post I'd had a few issues when building Airfix's 1:72 Hawker Typhoon.

Source: (Lower Image) Hyperscale

The issues centered around the base of the wings, the flexible nature of this piece had meant that when it came to fitting the wheel covers, to depict the aircraft in flight, they wouldn't fit without considerable trimming and so looked quite untidy.

Out of curiosity I decided to open up another kit and see if they would actually fit prior to assembly and, as shown in the picture below, they clearly did.

This got me thinking, maybe there was a another way to build this kit, starting with the lower wings so I didn't make the same mistake again. And while I was at it, I'd photograph each step and share.

The Build

The first step was to attach the cockpit floor and the wheel wells to lower section of the wings. The wheel covers were then inserted from the other side. As I'd already established, the fit was perfect.

I then attached one side of the fuselage to lower wing piece and fixed the air intake into the correct position. From here on in I continuously test fitted the other side of the fuselage and the top side of a wing. In order to make sure the fuselage fitted there was a slight bit of filing required at the rear of the air intake and each time it snapped into place which meant care had to be take when removing it.

Next I assembled the cockpit on the half of the fuselage that wasn't attached to the wings. I remove the locating pins that would fix into other side as they weren't really need. This was because I continued test fitting to make sure everything was in place and that it hadn't moved from the correct position. Once the glue had set the cockpit was painted. If you're adding the pilot, as I was, then you will see next to nothing, especially given that Typhoon cockpits were painted black inside.


Once the pilot had been put in place, (I filled away his back and cut off his feet to make him fit cleaner), it was time to glue the second side into place. Just make sure the tail wheel and the clear light to the base of the aircraft have been put in place.

After allowing time for the glue to set I moved onto the wings. The gun bays were put in place, but as I was doing an in flight model these would be covered up by the top halves of the wings. I also made sure I drilled out the holes for the rockets launchers as there's no indication of their position of the exterior side of the wing.

And there we have it, both the top halves of the wings attached without any issues. I then added the flap to the base of the air intake just to finish things off. The instructions tell you to do this when joining the two halves of the fuselage but on both builds I found it to be far too awkward. It's much easier just to remove one the pins and slot it in later.

A minor bit of filling was required, the join at the base of the air intake is not the best. But after that it was all ready for some paint to be applied and that will be my next build post.

Too Many Shades Of Grey (And Green) - Late War RAF Camouflage

It now been a considerable time since I actually completed a model aircraft, 5 months in fact. One satisfying part of that particular build was that I finally managed to replicate the early WWII RAF camouflage scheme of dark earth and dark green.

So that just left the late war scheme, which replaced the dark earth, (brown), with ocean grey as the air battle moved out over the English Channel and beyond. Should be pretty straight forward you'd have thought, so with that in mind I decided to give it a try.

I decided I would try two kits at the same time, both built straight out of the box as the main objective was the colour scheme. The kits, Airfix's 1:72 Hawker Typhoon IIb (A02041) and the Sptifire MK.IXc (A02065A). I'd picked them both up at the Home Bargain Store in the UK which had been selling off Airfix kits for less than half price at £2.99 each.

As well as the RAF camouflage I also wanted to compare pre-shading and not, and I wanted to try airbrushing invasion stripes rather than using decals.

Before I could start on the exterior there was the small matter of the interiors, and there was quite a difference between the two. The Spitfire was absolutely basic, which was surprising for a kit released in 2009 and for a kit which actually had some nice exterior details and fine panel lines which couldn't be said for all Airfix kits at that time.

The Typhoon on the other hand seemed almost over engineered. The cockpit floor also consisted of the wheel wells. The instrument panel, rear panel, seat and air intake all had to be fitted between the two halves of the fuselage meaning it took several goes of adding a piece, letting it dry, adding another and so on. It certainly looks good, but it seemed like it required a little more effort that was perhaps necessary.

After that it was a case of assembling the wings. The lower part of the wings left awful joints at the sides of the air intake and a huge step at the rear which would require considerable filling.

So while all that filling and sanding was going on I decided to get on with painting the Spitfire (the Spitfire went together easily).

I started by pre-shading with Vallejo Model Air Black, 71.057 and then painted the undersides with Barley White 71.051 which was highlighted with thinned coat of Pale Blue Grey 71.046.

Moving onto the upper sides I couldn't really find a suitable shade for Ocean Grey so I mixed Tamiya XF-18, XF-21, XF-24 to a ratio of 1:2:2 and sprayed the whole topside. I then started on the green by using Vallejo Model Air 71.016 over sprayed with 71.017 as I'd used for my early war scheme. My reasoning was that RAF aircraft used the same green throughout the war so I could just re-use the previous colours.

But this didn't look right. Was it because I was spraying green over a grey base coat, rather than dark earth? Quite probably, so I tried to correct it and things then went from bad to worse. Then I realised actually my Ocean grey was too dark anyway. Time to get the paint stripper out.

How not to do RAF Camouflage

So once again, I'd failed with Vallejo Model Air colours and to be honest, I'm getting a bit tired of this. OK, so my Tamiya mix hadn't worked out either, I can probably correct that though. However I then realised Tamiya had extended their paint range and introduced three RAF late war colours, XF-81, 82, 83 so tomorrow I'm going to pick them up.

Still, at least I had the Typhoon to fall back on. Except there was a problem. It turns out that the lower wing piece I'd mentioned was quite flexible and so the wheel covers wouldn't fit without considerable trimming and I was planning on depicting the aircraft in flight.

Good thing I bought two Typhoons...